none
StorSimple 8100 appliance console cable wiring RRS feed

  • Question

  • I have been trying to locate a wiring diagram for the 3.5mm to DB9F console cable supplied with the 8100.

    Monday, November 16, 2015 11:08 PM

All replies

  • Thanks for the reply but there is no wiring diagram on either of those sites - or any of the related pages.

    Tuesday, November 17, 2015 10:34 PM
  • Hello,

    Check this link:

    https://superwidgets.wordpress.com/2015/05/07/storsimple-8100-installation-step-by-step/

    Regards DOD..

    Wednesday, November 18, 2015 5:33 PM
  • Hi Phillip,

    It seems like you are looking for instructions on where to plug in the serial cable. Please refer to the cabling guide for 8100, look under the Serial Cabling section at this link. There is also a diagram for all the network ports on the StorSimple appliance including the serial port under the Network Cabling section at the same link.

    https://azure.microsoft.com/en-in/documentation/articles/storsimple-8100-hardware-installation/#cable-your-storsimple-8100-device

    Thanks!


    • Edited by Alpa KohliEditor Wednesday, November 18, 2015 6:13 PM
    • Marked as answer by Meghan Liese Wednesday, November 18, 2015 6:21 PM
    • Unmarked as answer by Phillip James Monday, January 18, 2016 11:27 PM
    Wednesday, November 18, 2015 6:13 PM
    Answerer
  • The reply marked as an answer was not.  I was not looking for "where to plug in the serial cable" and had already read the documents referenced.

    What I needed was a "wiring diagram", which means, to me, "which pin on the connector at one end of the cable is connected to which pin on the other end."

    I need to connect the serial port of the 8100 appliance to a terminal server.  Here is what I got from the helpful people at Seagate.  It is a wiring diagram for the serial cable supplied with the appliance:

    The DB9 female connector is P1 and the 3.5 mm connector is P2.

    Monday, January 18, 2016 11:44 PM
  • Hi Phillip,

    Great info thank you.

    There is no picture and there is no way to tell which pin of the 3.5mm Jack is which.

    The TIP of the stereo jack (P2) is considered to be PIN1 or PIN3 ?

    Thank you !

    Roberto



    • Edited by rbarrios Monday, February 15, 2016 8:54 PM
    Monday, February 15, 2016 8:53 PM
  • Hi Roberto,

    The tip of the stereo jack is considered to PIN 3 RX, the middle is PIN 2 TX and the base is PIN 1 GND. I am showing a schematic here. Please use it in conjunction with the pin table provided above by Phillips.

    Let me know if this helps, thanks!



    Wednesday, March 23, 2016 6:30 PM
    Answerer
  • <g class="gr_ gr_9 gr-alert gr_spell gr_inline_cards gr_run_anim ContextualSpelling multiReplace" data-gr-id="9" id="9">Thanks</g> you just saved me over $300  for something that cost me $4 to make thanks to the wiring diagram 

    115,200 baud, 8 data bits, 1 stop bit, no parity, and flow control set to None.

    I would never have thought about contacting <g class="gr_ gr_7 gr-alert gr_spell gr_inline_cards gr_run_anim ContextualSpelling ins-del multiReplace" data-gr-id="7" id="7">seagate</g>

    https://www.ebay.com.au/itm/New-Microsoft-Azure-StorSimple-Console-Serial-Cable-RS232-To-Auxiliary-71335-01/362248675802?hash=item5457b421da

    • Edited by MasterCATZ Wednesday, October 24, 2018 7:08 AM
    Sunday, October 14, 2018 6:49 AM